Jbl E10 User Manual download pdf (Page 3)

TROUBLESHOOTING

If there is no sound from

any of the speakers:

• Check that receiver/ampli-

fier is on and that a source is

playing.

• Review proper operation of

your receiver/amplifier.

If there is no sound coming

from one speaker:

• Check the “Balance” control

on your receiver/amplifier.

• Check all wires and connec-

tions between receiver/ampli-

fier and speakers. Make sure

no wires are touching other

wires or terminals and creat-

ing a short circuit.

• Make sure all wires are

connected. Make sure none

of the speaker wires are

frayed, cut or punctured.

• In Dolby* Digital or DTS

mode, make sure that the

receiver/processor is config-

ured so that the speaker in

question is enabled.

• Turn off all electronics

and switch the speaker in

question with one of the other

speakers that is working cor-

rectly. Turn everything back

on, and determine whether

the problem has followed the

speakers, or has remained in

the same channel. If the prob-

lem is in the same channel,

the source of the problem is

most likely with your receiver

or amplifier, and

you should

consult the owner’s manual for

that product for further infor-

mation.

If the problem has fol-

lowed the speaker, consult

your dealer for further assis-

tance or, if that is not possi-

ble, visit www.jbl.com for

further information.

If the system plays at low

volumes but shuts off as

volume is increased:

• Check all wires and connec-

tions between receiver/ampli-

fier and speakers.

• Make sure all wires are

connected. Make sure none

of the speaker wires are

frayed, cut or punctured.

• If more than one pair of

main speakers is being used,

check the minimum imped-

ance requirements of your

receiver/amplifier.

If there is no (or low) bass

output:

• Make sure the polarities

(+ and –) of the left and right

“Speaker Inputs” are con-

nected properly.

• Consider adding a powered

subwoofer to your system for

use with digital “.1” surround

formats.

If there is no sound from

the surround speakers:

• Check all wires and con-

nections between receiver/

amplifier and speakers. Make

sure all wires are connected.

Make sure none of the

speaker wires are frayed,

cut or punctured.

• Review proper operation of

your receiver/amplifier and its

surround sound features.

• Make sure the movie or TV

show you are watching is

recorded in a surround sound

mode. If it is not, check to see

whether your receiver/ampli-

fier has other surround modes

you may use.

•

In Dolby Digital or DTS mode,

make sure your receiver/pro-

cessor is configured so that

the surround speakers are

enabled.

• Review the operation of your

DVD player and the jacket of

your DVD to make sure that

the DVD features the desired

Dolby Digital or DTS mode,

and that you have properly

selected that mode using both

the DVD player’s menu and

the DVD disc’s menu.

NOTICE: Important Safety

Notes

• Proper selection of mount-

ing hardware and installation

of the wall brackets are the

responsibility of the customer.

• This product is not intended

for ceiling mounting.

Two Number 8 round head or

pan head screws should be

used per loudspeaker. The

screw head should be

between 5/16 inch (8mm) and

1/4 inch (6.3mm) in diameter,

and the screw should be at

least 2 inches (50mm) in

length.

When installing screws in any

wall, always use properly

selected wall anchors. Attach

two of the four self-adhesive

rubber pads that came with

the E10 loudspeaker to the

back of the enclosure in the

two bottom corners so that

the cabinet is spaced evenly

from the wall. Select a suit-

able mounting location on a

wall. (The ceiling is not a suit-

able mounting location.)

Drill two pilot holes, appropri-

ately sized for the specific

self-tapping screw or wall

anchor that you will be using.

The holes should be 8 inches

(203mm) apart. See Figure 1.

The holes should be 3/4"

(19mm) below where you

want the top of the enclosure

to be positioned. Use a car-

penter’s level to ensure that

the holes are even and that

the speaker will mount on the

level.

Install the two screws into

either a wooden wall stud or

anchor, and tighten them until

the back of each screw head

is about 1/8 inch (3mm) from

the wall. See Figure 2. Install

the loudspeaker by slowly

moving the cabinet toward

the screws so that the screw

heads clear the larger circu-

lar portion of the two key-

holes. Once both screw

heads have entered the key-

holes, the loudspeaker should

gently be lowered onto the

screw shafts. Check that the

loudspeaker is firmly locked

onto the screws by gently

pulling the speaker down and

forward.

WALL-MOUNTING (Model E10 Only)

8" (203mm)

1/8"

(3mm)

1 2 3 4

Comments to this Manuals

No comments

Jbl E10 User Manual Page 3

Comments to this Manuals

Related products and manuals for Microphones Jbl E10